NetWorking IPv6 Test(1st)

What multicast addresses does EIGRPv6 use?

1 Mark(s)

FF02::A
FF02::5
FF02::6
FF02::9

Which statement(s) about IPv6 addresses are true?
1. Leading zeros are required.
2. Two colons (::) are used to represent successive hexadecimal fields of zeros.
3. Two colons (::) are used to separate fields.
4. A single interface will have multiple IPv6 addresses of different types.

1 Mark(s)

1, 3 and 4
All of the above
1 and 3
2 and 4

Which of the following is true when describing a unicast address?

1 Mark(s)

These are your typical publicly routable addresses, just like a regular publicly routable address in IPv4.
Packets addressed to a unicast address are delivered to a single interface.
These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap.
These are like private addresses in IPv4 in that they are not meant to be routed.

Which statement(s) about IPv4 and IPv6 addresses are true? 1. An IPv6 address is 32 bits long, represented in hexidecimal. 2. An IPv6 address is 128 bits long, represented in decimal. 3. An IPv4 address is 32 bits long, represented in decimal. 4. An IPv6 address is 128 bits long, represented in hexidecimal.

1 Mark(s)

2 only
2 and 4
1 and 3 only
3 and 4

Which of the following is true when describing a link-local address?

1 Mark(s)

Packets addressed to a unicast address are delivered to a single interface.
These are your typical publicly routable addresses, just like a regular publicly routable address in IPv4.
These are like private addresses in IPv4 in that they are not meant to be routed.
These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap.

Which of the following is true when describing a multicast address?

1 Mark(s)

Packets are delivered to all interfaces identified by the address. This is also called a one-to-many address.
Packets addressed to a unicast address are delivered to a single interface.
Identifies multiple interfaces and is only delivered to one address. This address can also be called one-to-one-of-many.
These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap.

Which of the following is true when describing an anycast address?

1 Mark(s)

Packets addressed to a unicast address are delivered to a single interface.
This address identifies multiple interfaces and the anycast packet is only delivered to one address. This address can also be called one-to-one-of-many.
Packets are delivered to all interfaces identified by the address. This is also called one-to-many addresses.
These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap.

What two multicast addresses does OSPFv3 use?
1. FF02::A
2. FF02::9
3. FF02::5
4. FF02::6

1 Mark(s)

1 and 3
2 only
3 only
3 and 4

To enable EIGRP, which of the following would you use?
1. Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
2. Router1(config-if)# ipv6 router rip 1
3. Router1(config)# ipv6 router eigrp 10
4. Router1(config-rtr)# no shutdown
5. Router1(config-if)# ipv6 eigrp 10

1 Mark(s)

3, 4 and 5
1 and 3
1, 3 and 5
5 only

Which of the following is true when describing a global unicast address?

1 Mark(s)

These are like private addresses in IPv4 in that they are not meant to be routed.
Packets addressed to a unicast address are delivered to a single interface.
These are your typical publicly routable addresses, just like a regular publicly routable address in IPv4.
These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap.

To enable RIPng, which of the following would you use?

1 Mark(s)

Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
Router1(config)# ipv6 router eigrp 10
Router1(config-rtr)# no shutdown
Router1(config-if)# ipv6 router rip 1

Which of the following is true when describing a unique local address?

1 Mark(s)

These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap.
These are like private addresses in IPv4 in that they are not meant to be routed.
These are your typical publicly routable addresses, just like a regular publicly routable address in IPv4.
Packets addressed to a unicast address are delivered to a single interface.

To enable OSPFv3, which of the following would you use?

1 Mark(s)

Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
Router1(config)# ipv6 router eigrp 10
Router1(config-rtr)# no shutdown
Router1(config-if)# ipv6 router rip 1

You want to ping the loopback address of your local host(with IPv6). What will you type?

1 Mark(s)

trace 0.0.::1
ping 127.0.0.1
ping ::1
ping 0.0.0.0

What multicast addresses does RIPng use?

1 Mark(s)

FF02::5
FF02::9
FF02::6
FF02::A

NetWorking IPv6 Test(1st) : Question 1 of 15