NetWorking IOS and Security Device Manager Test(1st)

You type show running-config and get this output:

[output cut]
Line console 0
    Exec-timeout 1 35
    Password BIXPASSWD
    Login
[output cut]

What do the two numbers following the exec-timeout command mean?

You type show running-config and get this output:

[output cut]
Line console 0
    Exec-timeout 1 35
    Password BIXPASSWD
    Login
[output cut]

What do the two numbers following the exec-timeout command mean?

1 Mark(s)

If no commands have been typed in 1 minute and 35 seconds, the console connection will be closed.
If no router activity has been detected in 1 hour and 35 minutes, the console will be locked out.
If you're connected to the router by a Telnet connection, input must be detected within 1 minute and 35 seconds or the connection will be closed.
If no command has been typed in 35 seconds, the console connection will be closed.

What keystroke will terminate setup mode?

1 Mark(s)

Ctrl+^
Ctrl+Z
Ctrl+C
Ctrl+Shift+^

Which command will delete the contents of NVRAM on a router?

1 Mark(s)

erase start
delete startup-config
erase NVRAM
delete NVRAM

Which of the following commands displays the configurable parameters and statistics of all interfaces on a router?

1 Mark(s)

show versions
show running-config
show startup-config
show interfaces

You type Router#sh ru and receive an % ambiguous command error. Why did you receive this message?

1 Mark(s)

The command is being executed from the wrong router mode.
There is more than one show command that starts with the letters
The command requires additional options or parameters.
There is no show command that starts with

You type the following command into the router and receive the following output:

Router#show serial 0/0
        ^
% Invalid input detected at '^' marker.

Why was this error message displayed?

You type the following command into the router and receive the following output:

Router#show serial 0/0
        ^
% Invalid input detected at '^' marker.

Why was this error message displayed?

1 Mark(s)

Part of the command is missing.
You need to be in privileged mode.
You cannot have a space between serial and 0/0.
The router does not have a serial0/0 interface.

How many simultaneous Telnet sessions does a Cisco router support by default?

1 Mark(s)

What command do you type to save the configuration stored in RAM to NVRAM?

1 Mark(s)

Router#copy run startup
Router (config) #copy running-config startup-config
Router#copy starting to running
Router (config) #copy current to starting

Which of the following commands will configure all the default VTY ports on a router?

1 Mark(s)

Router (config) #line vty 0 4
Router (config) #line vty all
Router (config-if) #line console 0
Router#line vty 0 4

You set the console password, but when you display the configuration, the password doesn't show up; it looks like this:

[output cut]
Line console 0
    Exec-timeout 1 44
    Password 7098C0BQR
    Login
[output cut]

What cause the password to be stored like this?

You set the console password, but when you display the configuration, the password doesn't show up; it looks like this:

[output cut]
Line console 0
    Exec-timeout 1 44
    Password 7098C0BQR
    Login
[output cut]

What cause the password to be stored like this?

1 Mark(s)

service-password-encryption
service password-encryption
exec-timeout 1 35
encrypt password

If you delete the contents of NVRAM and reboot the router, what mode will you be in?

1 Mark(s)

Global mode
NVRAM loaded mode
Setup mode
Privileged mode

Which of the following commands will display the current IP addressing and the layer 1 and 2 status of an interface?
1. show version
2. show protocols
3. show interfaces
4. show controllers
5. show ip interface

1 Mark(s)

None of the above
1, 2 and 4
3 and 4 only
2, 3 and 5

Which of the following commands sets the secret password to Cisco?

1 Mark(s)

enable password Cisco
enable secret cisco
enable secret password Cisco
enable secret Cisco

What is the problem with an interface if you type show interface serial 0 and receive the following message? "Serial0 is administratively down, line protocol is down."

1 Mark(s)

The administrator has the interface shut down.
The administrator is pinging from the interface.
The keepalives are different times.
No cable is attached.

What layer of the OSI model would you assume the problem is in if you type show interface serial 1 and receive the following message? "Serial1 is down, line protocol is down."

1 Mark(s)

Network layer
Physical layer
Data Link layer
None. It is a router problem.

You want to totally reinitialize the router and replace the current running-config with the current startup-config. What command will you use?

1 Mark(s)

copy start run
copy run start
replace run start
reload

Which command will show you whether a DTE or a DCE cable is plugged into serial 0?

1 Mark(s)

show serial 0 controllers
sh int serial 0
show controllers serial 0
sh int s0

You need to find the broadcast address used on a LAN on your router. What command will you type into the router from user mode to find the broadcast address?

1 Mark(s)

show startup-config
show protocols
show running-config
show interfaces

If you wanted administrators to see a message when logging into the router, which command would you use?

1 Mark(s)

message motd
banner message motd
banner motd
message banner motd

NetWorking IOS and Security Device Manager Test(1st) : Question 1 of 19